I originally wanted a bullet mold which I could use to cast a heavy 300blk bullet which was easy to cast, coat, load, and shoot for plinking in my 300 blk AR15 at subsonic speeds. I tried a few of the already available molds but had feeding issues, undersized issues, boat tail issues, or issues […]

I recently purchased a mold to cast .45 caliber bullets for my 1911.  In this video, I use the mold to cast three different style bullets, and then powder coat and size them.  This mold has no lube groove, and the bullets must be coated with Hi-Tek or powder coat.

Several years ago, I purchased a lightly used brushed-chrome model of the Desert Eagle handgun chambered in 50 Action Express.  Finding the .50 cal bullets for it has been tricky at times–other times it has been quite expensive.  To save money and to not be reliant on bullet availability at the local or online shops, […]

300 BLK Cast Bullet For Dummies (NOE 310-225-RN) Start to Finish!

I wanted to see how much penetration these subsonic 600 gr 458 socom bullets would have through water (milk jugs). We saved up a bunch of jugs and went out to test. Watch the video for the results. Test Firearm: 10.5″ 458 Socom Upper by Radical Firearms Registered SBR lower Silencerco Hybrid Suppressor Ammo Details: […]

Powder coating session for my recently cast 9mm bullets. I cast these bullets from the NOE HTC358-133-RN mold.

In this video I show most of the steps from start to finish on how I make one of my favorite milk jug exploding 45-70 loads. All the details should be in the video, but if you have any questions, feel free to leave a comment here and I will respond as quickly as I […]

My first casting session with the NOE HTC358-133-RN two cavity mold for 9mm. This is also my first casting session with the PID I recently assembled.

‘In the beginning…’ I started casting and ‘Lube-Sized’ my rifle/pistol projectiles…back then, the choice of lube was a hot topic and there were many heated exchanges about which lube would allow particular advantages. Some lubes required a ‘heater’ to be installed under the Sizer, some not. ‘Leading’ of the barrel was a problem when the […]

I go through the entire process of casting, powdercoating, loading, and shooting some hard cast round nose bullets using the high quality NOE bullet mold for my 10mm handguns.  I had wanted a round nose bullet for 10mm plinking loads.  Something that would feed simply and flawlessly in each of my 10mm handguns and carbines.  This bullet mold seems to do the trick.

315 Gr 338 Spectre Subs -- Now I have ammo!

I recently cast bullets for 9mm with the NOE HTC358-133-RN mold, powder coated them with Eastwood Lime Green, and sized them to .358". I am now working up a load with Unique powder, which is a challenge since there is no published load data for this or a similar bullet. I am shooting these from my Beretta 92S.

Today, I show in this video the entire process from start to finish how I cast, powder coat, load, and shoot some 250gr coated cast lead hollow points in the 44 magnum. This is one of my "go to" loads for blasting milk jugs without much recoil.  These loads are perfect for maximum explosion with minimal recoil--great for those milk jug duels with the buddies.  Got questions?  Feel free to leave me a comment below, and I will do my best to answer it!

I recently cast bullets for 9mm with the NOE HTC358-133-RN mold, powder coated them with Eastwood Lime Green, and sized them to .358". I am now working up a load with Alliant e3 powder, which is a challenge since there is no published load data for this or a similar bullet. I am shooting these from my Beretta 92S.

3 months ago I posted a video about "My New Mobile Bullet Casting Bench". Today I finish the upgrades. I added the NOE Lead Pot Mould Guide. I also added ventilation for my casting pot.

I was finally able to get to the range and gather some velocity data using Ramshot True Blue by Western Powders. The two bullets used were the Lee 356-124-2R and the NOE HTC-358-133-RN. The lighter Lee bullets seemed to prefer a lighter charge while the heavier bullet from NOE preferred a higher charge. This goes […]

"Thank you for helping us make it 10 years! In appreciation we are offering 25% off all our stock inventory. 7 Days only, March 16th thru the 22nd."

Today I'm going to test how well Ramshot True Blue flows through my powder measure.

I recently cast up a bunch of bullets with my new NOE HTC358-133-RN mold for 9mm. These bullets cast at an average of 134 grains with my alloy. I have sized these to .358", and today I decided to test them from my 4" Taurus Model 66 loaded in both 38 special and 357 magnum.

A while back I wanted to see what the lightest bullet I could load in my 300 blk would be. I worked my way all the way down to a round ball load. Someone asked me if I was worried about a baffle strike with the round ball–I asked them, ” what do you think […]

It's cold outside.  YouTube has given my channel its second strike and I'm not allowed to upload anything to their servers for a couple of weeks.  Should I curl up in front of the fireplace and wish for warmer days?  Not hardly! There's hog hunting, new firearms, and plenty more going on...

Return of The 9mm Video! (NOE HTC358-133-RN Bullet Mold)

In today's video, I am powder coating my recent cast 9mm rounds. I am using Harbor Freight Red powder. I am having trouble with the powder sticking to the bullets. After watching several videos from authors of The Reloaders Network, I'm still not getting the results I want. All the rounds are usable, but they just don't look the best. Some have thin and thick spots, and some have bare spots. Factors such as weather, humidity, and types of plastic containers could be affecting my results. All the rounds were sized to .356 using a NOE Sizing Die.

338 Spectre Cast 250gr Subsonic Bolt Gun Loads (NOE341-245-SP)